Maytag washer power button flashing

Quick Answer. To turn off or deactivate the control lock feature on the Maytag washer, press and hold the control lock button for up to three seconds or until you see the countdown displayed on the control panel. Once the control lock is turned off, the LC or LoC code will disappear. Most Maytag washing machines include either a standalone ...

Push the door closed firmly within 3 seconds of pressing the Start button to prevent this from happening. Lights may also blink on the control panel if the dishwasher was set for a Delay Start and the door was unlatched. The lights will stop blinking and the Delay Start cycle will begin after you've pressed the Start button and fully closed ...To turn off the Control Lock, press the Options key that says "Control Lock Hold 3 Sec" under it for 3 seconds. If the dishwasher has a dedicated Control Lock button in the Options selections, press and hold CONTROL LOCK for 3 seconds (press the words "Control Lock). NOTE: You may need to disable Sleep Mode by pressing either Start/Resume or ...Plug power cord into a grounded 3 prong outlet. Do not use an extension cord. Check to see if a household circuit breaker or Ground Fault Circuit Interrupter (GFCI) outlet has tripped. If so, reset the circuit breaker or Ground Fault Circuit Interrupter. If the washer is on a fuse box, check to see if a fuse has blown and replace it, if necessary.To fix this issue: Locate the float switch. This will be at the bottom of the dishwasher tub. Make sure the float can move freely up and down. You might need to unscrew the cover to check if it is moving freely. When you move the float, listen carefully to see if you can hear the relay switch click.Maytag manufactures a wide array of household products, including dishwashers, washers, dryers, refrigerators, microwaves, compactors and ranges. Maytag has been manufacturing hous...This is how to properly reset a Maytag washer: Step 1: Unplug the machine. Step 2: Press and hold the POWER/START button for 5 seconds. Step 3: Hold down the PLAY/PAUSE button for 5 seconds. Step 4: Plug the machine back in and press POWER to restart.

STEP 3: CLEAN IN AND AROUND THE WASHER DOOR. Remove any clothing or items from the washer. Open the washer door or lid and wipe down the inside glass or metal with a damp cloth. On front load washers, wipe the outside of the rubber door seal. Then lift up the edge and wipe the interior surfaces as well.If you’re experiencing problems with your washer and the lid lock light is flashing, the first thing to do is unplug the machine for about 10 minutes and then plug it back in. This will reset your washer, as well as its flashing light which means that you know everything is still in working order manually. You might also press and hold the ...Do not use an extension cord. Check to see if a household circuit breaker or Ground Fault Circuit Interrupter (GFCI) outlet has tripped. If so, reset the circuit breaker or Ground Fault Circuit Interrupter. If the washer is on a fuse box, check to see if a fuse has blown and replaced it, if necessary. If the problem continues to occur, call an ...Most Powerful Cleaning in its class driven by the Heavy Duty cycle with Extra Power button. (Based on cleaning score of 18-lb load, among leading top load brands, 5.0-5.4 cu. ft. capacity impeller washers, vs. comparable cycles.) ... We don't just tell you a Maytag washer will get your clothes clean for years: we confidently back our washers ...The Maytag MVWB865GW is a washing machine that offers efficient cleaning performance. With its large capacity, it can handle sizable laundry loads, making it suitable for households with significant amounts of laundry. The appliance features a variety of cycle options, enabling users to choose the best setting for their specific needs.The Power Outage indicator (on some models) lets you know if the power supply to the refrigerator has been off and the freezer temperature has risen. The control panel display will read "Power Outage," and an alert tone will sound three times. Touch any button to stop the tone, and touch any button again to turn off the Power Outage icon.GET MORE CAPACITY AND POWER WITH A MAYTAG ® TOP-LOAD WASHER. Large and extra-large capacity top load washing machines help tackle your family's toughest messes. Maytag ® top load washers offer agitator or impeller options, deep clean options, steam-enhanced cycles, optimal dispensers and stainless steel wash baskets.

If the sensing light on your Maytag Centennial washer is on and the lid lock is flashing, it typically indicates an issue with the washer that needs attentio...In this video, we will guide you through the process of resetting your Maytag washer. A reset can help resolve various issues, such as error codes, unrespons...BBY01-806474495703 5-Year Standard Geek Squad Protection I have this plan too. And product came with 10 years warranty plan. model number for washer - MHW6630HW2 …1. Lid Lock Error. If your lid lock sensing light is blinking, then the reason might be that your Maytag washer’s lid is not properly closed. There might be another …

Ynw melly verdict court tv.

To unlock a Maytag washer, you can follow these steps: 1. If the washer was installed without water hoses attached and turned on, it may attempt to drain for 8-10 minutes before the door unlocks. 2. Ensure that the drain hose is connected properly and not inserted more than 4.5 inches into the standpipe. 3.Method Meets Madness. 4.56K subscribers. Subscribed. 2. 476 views 4 months ago #ErrorCodes #DIYRepair #HomeAppliances. Is the sensing light on your Maytag washer blinking, causing laundry...To clear the code, press the PAUSE button twice and the POWER button once. F9 E1: Draining water takes too long. Condition: Draining water is taking too long (usually more than eight minutes). Parts where possible failure may take place: Water drain hose, washer drum. How to fix the problem yourself: This is one of the trickier Maytag washer ...When your Maytag washer turns on but won't start there may be a problem with the door closure. As a safety precaution, the washer won't start if the door isn't properly shut and latched. Always close the door firmly and allow 10 seconds for the latch to engage. Check the door for trapped clothing that may prevent it from closing completely.

Get the heavy duty washing machine that delivers the Most Powerful Cleaning in its class driven by the Heavy Duty cycle with Extra Power button.*. The Extra Power button boosts stain fighting on any wash cycle, including the Quick Wash cycle. Smart washer features like remote start and cycle notifications help you efficiently manage laundry ...If F8 E1 or LF (too long to fill) appears in the display, the washer is taking too long to fill or the washer is filling and draining. It's possible the drain hose extends more than 4.5" (114 mm) into the standpipe. Check the plumbing for the correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.Try these quick fix tips before going through all the causes and fixes for lid light flashing: 1 – Unplug the washer for 10 minutes and this may reset the washer and clear the flashing light. 2 – Press and hold the “END OF CYCLE / CYCLE SIGNAL” button (s) for 20 seconds and this should reset the washer and clear the flashing light.Product Description. Smart Top Load Washer with Extra Power - 5.2 cu. ft. With every laundry cycle, Maytag delivers powerful cleaning you can depend on with the Power™ agitator. Use Extra Power for boosted stain fighting on any wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper water levels ...Product Description. Smart Top Load Washer with Extra Power - 5.2 cu. ft. With every laundry cycle, Maytag delivers powerful cleaning you can …Product Description. Smart Top Load Washer with Extra Power - 5.3 cu. ft. With every laundry cycle, Maytag delivers powerful cleaning you can depend on with the Power™ impeller. Use Extra Power for boosted stain fighting on any wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper water levels ...Brand new Electrolux washer never used has blinking start button and won't start. Contractor's Assistant: Is your Electrolux washer top ... but I am happy to assist you further. Please try to unplug the unit from the power source or turn off the electrical breaker for 10 minutes, and then plug it back in. ... I have a Maytag Maxima washer ...Laundry day can be a breeze when you have a reliable top-load washer like a Maytag…Alternative reset procedure 2 (this works for some Maytag Bravos XL washer series models) Rotate the dial (Cycle Selector knob) till it is at 12 Oclock position (turn dial 1 counter-clockwise -or right- full turn until you’re back to 12) You then rotate the dial three (3) turns clockwise (right). Next, rotate the dial one (1) turn counter ... Power the appliance off and then turn it on again. Press and quickly release the Wifi Connect button. Do NOT hold for 3 seconds, even if the button says to do so. Return to the app to complete the connection steps. If you are still experiencing issues, contact the Customer Experience Center at (866) 333-4591, Mon-Tue 8am to 6pm, Wed-Fri 9am to ... If no indicators come on after pressing the START button, go to TEST #1, page 12. EXITING THE SERVICE DIAGNOSTIC TEST MODES Press and hold the START button for 3 seconds at any time to exit diagnostic test modes. Washer will exit diagnostic test modes after 5 minutes of inactivity or unplugging the power cord. MODE SOAK / W ASH RINS E FINA L ...Understanding the Maytag Bravos XL Washer Reset Preparing for a Washer Reset Initiating the Power Disconnect Method Disconnecting Power Wait Time Accessing the Washer's Internal Components Opening the Top Panel Locating Internal Reset Button Executing the Standby Mode Reset Activating Standby Mode Completing the Reset …

Cause 1 Power outage reset. After a power outage the washer display may beep and/or flash a code like PO for power outage or PF for power failure. In most cases you will need to press a button to reset the alarm. You can also try turning the breaker off for a few seconds then back on. Refer to the owner's manual for specific information.

May 2, 2023 ... This video is a tutorial on how to enter diagnostic mode on a Whirlpool or Maytag washer with this style console, as its different than ...The Power Outage indicator (on some models) lets you know if the power supply to the refrigerator has been off and the freezer temperature has risen. The control panel display will read "Power Outage," and an alert tone will sound three times. Touch any button to stop the tone, and touch any button again to turn off the Power Outage icon.The Maytag MVW6200KW is a washing machine designed to provide efficient and reliable laundry care. It is equipped with a variety of features to enhance the washing experience. With a sizable capacity, this washing machine can accommodate large loads of laundry, making it suitable for households with heavy laundry needs.The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. ... once to return it to the 3 o’clock position. If the process has worked, the control panel lights should start blinking. ... Hold down the Delicates and Knits button for five seconds. The washer’s LED display should now …Hi my Maytag washer is set at delicates with 45 minutes. ... Maytag Bravos XL Model MVWB835DW3 Won't let me select a wash type Normal load light blinking ... It turns on , but the selection knob, start button wont start the washer and other buttons won't change anything.This 4.5 cu. ft. capacity top load washer from Maytag delivers the stain-fighting power that's built to handle tough loads. Use the Deep Fill option for more water when you want it, while the Power agitator knocks the stubborn out of stains with a 360° wash action. 2-Extra Rinse options help thoroughly clean clothes by rinsing away messes and ...First of all, be sure the washer is in standby mode (plugged in with all indicators off). Select any three (3) buttons (except POWER) and follow the steps below, using the same buttons. Remember the buttons and the order that the buttons were pressed. Within 8 seconds, • Press and Release the 1st selected button,This 4.7 cu. ft. capacity top load washer from Maytag delivers the stain-fighting power that's built to handle tough loads. Use Extra Power for boosted stain fighting on any wash cycle while the Power agitator uses a 360-degree wash action to break up messes and knock the stubborn out of stains.Jun 6, 2020 ... ... Washer ⭐ ✓ Press the "Power/Cancel" button. ✓ Push the appropriate button to ... Why is my lid lock light flashing on Maytag washer? How do you ....Turn off power to Maytag dishwasher. Remove control panel trim. Find securing screws or clips around edges of panel. Disconnect touchpad wires. Note positions of wires to reconnect properly later. Remove touchpad mounting screws. A few small screws attach touchpad within panel. Detach old touchpad from control panel.

Mondo owada sprites.

Kelsie and brandon catfish where are they now.

Turn off your washer by pressing the power button or simply unplugging it from the power source. Wait for approximately 30 seconds to 1 minute. Plug the washer back in or press the power button to turn it on again. Once the washer has powered on, select the “Reset” option from the control panel.After a power outage the dryer display may beep and/or flash a code like PO for power outage or PF for power failure. In most cases you will need to press a button to reset the alarm. You can also try turning the breaker off for a few seconds then back on. Refer to the owner's manual for specific information. Cause 2 Check Fault Codes.Reach behind the washer and unplug it from the wall. Wait for 60 seconds, then plug the washer back in. [8] 2. Lift and close the lid 6 times within 12 seconds. Right after plugging the machine back in, quickly open and close the lid 6 different times. Do this within 12 seconds to reset the motor in the machine.Product Description. Get the heavy duty washing machine that delivers powerful cleaning you can depend on with the Power™ agitator. The Extra Power button boosts stain fighting on any wash cycle with a dual-temperature wash, including the Quick Wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper ...The spin light blinking on a Maytag washer means there’s an issue with the drain pump. According to Maytag, if the drain pump is on for 10 minutes but it detects there’s still water in the washing machine the spin light will blink. It can also blink if it’s overloaded and can’t spin.Power outage is a pretty common reason why your Maytag washer is beeping while running. Water level problem: If the washer has a low water level, it will give a signal. Generally, the Maytag washer has a specific level of water that is necessary. If the water level is too low, you might hear a beeping sound while running the washer.With every laundry cycle, Maytag delivers powerful cleaning you can depend on with the Power impeller. Use Extra Power for boosted stain fighting on any wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper water levels,* while the built-in water faucet delivers a quick rinse or a long soak. Plus, smart features …Shop Maytag 5.2 Cu. Ft. High Efficiency Smart Top Load Washer with Extra Power Button Metallic Slate at Best Buy. Find low everyday prices and buy online for delivery or in-store pick-up. Price Match Guarantee.1 Answer. Hi @David Morgan. Did you check the cable between the main board and the control panel for continuity i.e. fractured wiring perhaps, and also check for corrosion etc on the cable connections? Here's the tech sheet for the washer that may help. On p.11 it gives the checks to be made for a won't power up problem. ….

I have a maytag top load washer, model MVWB865GW0 and it won't start--it just beeps. ... My washer has power and the cycle is light up and flashing but the start button just beeps over and over when I try to start it and I've unplugged and replugged and it won't move off ... I gave a Maytag washer MOD MVWB835DW4 that has power but won't start. ...We bought this Maytag washer a couple years ago model (MVWC465HW2) and we have had nothing but issues with it, but it goes through the wash cycle but when it gets to rinse it seems to get stuck and the rinse light starts flashing and will continue flashing forever until we home the button down to cancel the cycle, but then the lid stays locked for several …6 Answers. Cause 1. User Control and Display Board. To determine if the user control and display board is defective, try pressing the buttons on the control panel. If some of the buttons work, but others do not work, the control and display board might need to be replaced. Additionally, if the display is not working, check the power to the user ...Done right ASAP-If the "sensing /fill" is the only light on and it's flashing then the cycle has paused. Push the PAUSE button once and the light should be on but not flashing and the cycle should continue within about 10 min depending on water pressure. You could have a slow fill. Unplug unit.... - Kenmore 110 Series Washing MachineF13 DISPENSER CIRCUIT ERROR. F14 EEPROM ERROR. F15 MOTOR CONTROL UNIT (MCU) ERROR. FdU DOOR UNLOCK ERROR. FdL DOOR LOCK ERROR. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) First of all, be sure the washer is in standby mode (plugged in with all …Delay Start, use "+" and "-" to set the delay time to "0," or touch Power. START/PAUSE BUTTON Touch and hold the Start/Pause button for up to 3 seconds or until the washer starts to begin the selected cycle; touch again to pause a cycle. NOTE: If the washer is spinning, it may take several minutes to unlock the lid. CYCLE MODIFIERSClose the washer lid before starting the washer. Some will fill with the lid open but will not advance if the lid remains open. The washer will drain after 10 minutes if the lid remains open. Some models have lights on the console, which show when the lid is locked. When lit, the lid is locked and cannot be opened without pausing the cycle.Product Description. Get the heavy duty washing machine that delivers powerful cleaning you can depend on with the Power™ agitator. The Extra Power button boosts stain fighting on any wash cycle with a dual-temperature wash, including the Quick Wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper ...Product Description. Smart Top Load Washer with Extra Power - 5.2 cu. ft. With every laundry cycle, Maytag delivers powerful cleaning you can depend on with the Power™ agitator. Use Extra Power for boosted stain fighting on any wash cycle. The Deep Fill option delivers more water when you want it with your choice of deeper water levels ... Maytag washer power button flashing, Is your Amana top load washer not starting or operating because the lid lock is flashing? Find out the possible causes and solutions on this page., The Maytag 4.8 cu. ft. capacity washer with Extra Power delivers boosted stain fighting on any wash cycle while the Power Impeller helps dissolve soils with a vigorous wash motion. This Deep Fill washer delivers more water when you want it while the built-in water faucet rinses, spot treats or soaks clothes right in this heavy duty washing machine., This top loader Maytag washer with the agitator does a good job. It’s 5.2 Cu Ft, slightly smaller than the 5.3 Cu Ft washer without an agitator that we really wanted, but that was out of stock without any realistic assessment of when it would be back in stock. ... Maytag - 4.7 Cu. Ft. High Efficiency Smart Top Load Washer with Extra Power ..., Contact Us. (800) 344-1274 U.S. (800) 688-2002 Canada. Launch Live Chat. Maytag Customer Service: 553 Benson Road. Benton Harbor, MI 49022. Create an account in the Owners Center to quickly access material for your registered appliances. For additional help maintaining your appliances beyond manuals and guides, check out our Product Help and ..., OK so that falshing start button means that the dishwasher thinks the touchpad has an internal short inside. It sounds like you've already tried to flip the circuit breaker off or cut power to the dishwasher and that didn't fix the problem so unfortunately that means your touch control panel would need to be ordered and replaced., I have a maytag top load washer, model MVWB865GW0 and it won't start--it just beeps. ... My washer has power and the cycle is light up and flashing but the start button just beeps over and over when I try to start it and I've unplugged and replugged and it won't move off ... I gave a Maytag washer MOD MVWB835DW4 that has power but won't start. ..., CYCLE TIME: 6 - 8 minutes. 6. High temp. The high temperature option on your dishwasher will use hot water to help remove baked on food messes from your dishes. With this cycle the temperature is raised to a minimum of 130°F. CYCLE TIME: Adds 5 - 13 minutes to wash cycle. 7., Press the Start Button once. Unplug the washer or disconnect power. Wait 10 seconds, and reconnect power. Washer should not start and all LED's should be off. If washer does not automatically start, the process is complete. Link the information and document as a Save a Call. If the washer restarts within 10 seconds, schedule service. , Cycle Power. Sometimes the appliance just needs to be rebooted or restarted. Power the appliance down by turning off the circuit breaker (s) or unplugging for one (1) minute. Power the appliance up by turning on the circuit breaker (s) or plugging back in. Verify the operation of the control panel/display. , Now none of the lights work including the power button. I unplugged the washer for ~10 minutes, plugged in and the lights will not come on. Help! Thank you. Contractor's Assistant: I'm sorry to hear about the trouble you're experiencing with your Maytag washer. Has this issue with the flashing sensing light and unresponsive buttons happened ..., This washer has sensors that detect the water supply and requires both hoses to have water going to the water valve. If it does not detect both water supply hoses are turned on, the control detects a problem with the water pressure sensor. The lid will lock, and the machine will enter a pump out mode for 8 minutes., 6 Answers. Cause 1. User Control and Display Board. To determine if the user control and display board is defective, try pressing the buttons on the control panel. If some of the buttons work, but others do not work, the control and display board might need to be replaced. Additionally, if the display is not working, check the power to the user ..., Noisy Spin. Cause – Bad bearing. 6. Agitator Problem (Washer Won’t Agitate) Faulty agitator, drive belt, wash plate, drive motor, motor coupling, agitator repair kit, or door lock. 7. Drainage Problem (Washer Won’t …, This 4.7 cu. ft. capacity top load washer from Maytag delivers the stain-fighting power that’s built to handle tough loads. Use Extra Power for boosted stain fighting on any wash cycle while the Power agitator uses a 360-degree wash action to break up messes and knock the stubborn out of stains., Maytag top load washer model number - Answered by a verified Appliance Technician We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them., First things first, turn off your Maytag washer. Disconnect the washer from the electric supply. Wait for some time before turning on the machine again. It is recommended to keep it off for 3-5 minutes. Now, plug in the socket and press the start button. To reset the motor settings, lift the top lid up and down six times to reset the motor ..., Most Powerful Cleaning in its class driven by the Heavy Duty cycle with Extra Power button. (Models with Extra Power option: MVW8230H, MVW7230H. Based on cleaning score of 18-lb load, among leading top load brands, 5.0-5.4 cu. ft. capacity agitator washers, vs. comparable cycles.), To reset the dishwasher control panel: Disconnect from the power source for one minute. After one minute, reconnect the dishwasher to its power source. If your dishwasher is plugged into an outlet, unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard wired to the power supply, turn the breaker off at the home ..., Possible Solutions. Electronic Touch Pad Information. When using the touch control, touch on the name to operate, not the lights. Is the control locked (control on the back …, Past 7 Days: 97. Past 30 Days: 408. All Time: 168,700. The problem might be that the black pin (about 3/8" long and 1/8" in diameter), that normally sticks out of the frame of the washer at about the 2 o'clock position, and which is pushed in when the door closes, has broken off. If this pin breaks off, the washer will not recognize that the ..., Maytag front load washer model #mhw5630hw flashing 0:00 and says ERR when dial is turned. Unplugged for 1 minute and plugged back in, did not fix. Unplugged for hours and plugged back in, did not fix. …, First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won't start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it., Most Powerful Cleaning in its class driven by the Heavy Duty cycle with Extra Power button. (Models with Extra Power option: MVW8230H, MVW7230H. Based on cleaning score of 18-lb load, among leading top load brands, 5.0-5.4 cu. ft. capacity agitator washers, vs. comparable cycles.) ... We don’t just tell you a Maytag washer will get your ..., STEP 3: CLEAN IN AND AROUND THE WASHER DOOR. Remove any clothing or items from the washer. Open the washer door or lid and wipe down the inside glass or metal with a damp cloth. On front load washers, wipe the outside of the rubber door seal. Then lift up the edge and wipe the interior surfaces as well., OUR HEAVY DUTY WASHING MACHINE OPTION BOOSTS STAIN FIGHTING ON ANY WASH CYCLE. Extra Power boosts stain fighting on any wash cycle with an intense pre-wash and extra agitation so you can walk away while stains wash away. 1. Appliance must be set to remote enable. WiFi & App required., Try these quick fix tips before going through all the causes and fixes for lid light flashing: 1 – Unplug the washer for 10 minutes and this may reset the washer and clear the flashing light. 2 – Press and hold the “END OF CYCLE / CYCLE SIGNAL” button (s) for 20 seconds and this should reset the washer and clear the flashing light., Maytag washer MWVW4505MW1. Contractor's Assistant: When does the blinking light occur? Is it a specific pattern or does it blink continuously? First time I have used the washer. Loaded the washer, pressed the power button and the hold to start button. Sense button is flashing. Has been for 10 minutes, Lid Lock Flashing. To allow for higher spin speeds, the lid will lock and the Lid Lock light will turn on. When this light is lit, the lid is locked and cannot be opened. When this light is blinking, the washer is paused. When this light is off, the lid can be opened. If you need to open the lid to add a garment after this point, the lid will ... , Turn the dial counter clockwise one turn to reach the 3 o' clock position. After this, all the lights on the panel should start blinking. Turn the dial counter clockwise 4 settings or until the rinse light switches on. Press the start button. This will calibrate the washer which should reset the appliance., Jun 6, 2018 ... ... Button for 3+ seconds. 3) Close the LockBox ... How to open Whirlpool commercial Duty washer ... Code F02 or F2 Error Maytag Washer Machine - How to ..., A faulty lid switch: When the lid switch fails to function properly, it can cause the door to remain locked and the light to blink. A malfunctioning actuator motor: The actuator motor is responsible for controlling the locking mechanism of the washing machine door.If it is faulty, the door may stay locked and the light may blink. An issue with the drain pump: A malfunctioning drain pump can ..., Shop Maytag 4.2 Cu. Ft. High Efficiency Top Load Washer with Dual-Action PowerWash Agitator White at Best Buy. Find low everyday prices and buy online for delivery or in-store pick-up. ... Maytag - 4.5 Cu. Ft. High Efficiency Top Load Washer with Extra Power Button - White. User rating, 3 out of 5 stars with 8 reviews. (8) $764.99 Your price ..., Summary. Maytag Washing Machine Start Button Not Working. Disable Child Lock. Reset your Washing Machine. Faulty Control Board. Conclusion. Is your Maytag …