Ford axle identification

It's worth noting that rear axles can sometimes be positively identified by a casting number and date stamped on the differential cover or axle tube. However, road debris, dirt, grime, and general age can obscure these numbers. Fortunately, you can tell a lot about a rear axle by its shape and number of bolts on the differential housing.

Ford axle identification. Ford axle code 39 is a specific code assigned by Ford to identify the type and specifications of the rear axle in a vehicle. The axle code indicates specific details such as gear ratio, differential type, and other important information related to the axle assembly. Understanding the axle code is essential when it comes to replacing or ...

The first thing you should look for is the Safety Compliance Certification Label. It could be on any door panel, front or back. Look for the axle and note the code under the axle. By the axle ratio, you can tell what rear-end your Ford F150 has. For detailed information about the rear end of your truck, read this full article.

Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger.This is every number on the axle. The BOM does not exist anymore. It appears the brakes are off a 77.5 -79 f350 dana 60. But I assume the 44 6ef on the pumpkin indicates it's a 44. Anything else you guys need a picture of let me know please. The wheel bearings are so bad I don't want to drive it. Attached Images.The different types of early Ford axles are easy to identify by referring to the picture on the right, which was scanned from an old magazine article that was written by Neal East. The 1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches. 1932 axles were the first Ford axles to be made with a ...There are several common rear axle codes used in Ford Ranger models. Some examples include F7, R8, and H9. Each code represents different gear ratios and axle specifications. Familiarizing oneself with these codes enables owners to identify the exact axle equipped in their Ford Ranger and understand its capabilities. The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ...

Personally, I would suggest the 1957/72 F100 9" as it fits. I don't know if the others will and all the others have specific R & L axle shafts, while the F100's are the same R & L. F100: 1957/67 have 11" x 1 3/4" rear brakes, 1968/72 have 11 x 2 1/4" rear brakes. diff/axle identification.Ford Rear Axle Assembly Identification - Page 14. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.The 1985 to 1991 Ford F350 Dana 60 axles have a unique to Ford, reverse spiral ring and pinion set available in either 3.54 or 4.10 gear ratios. Axle Type: Mono Beam 1-piece iron housing, 4x4 front steer with full-floating axle shafts, and dual piston caliper disc brakes Cover: 10 Bolt, 12" high Ring Gear: 9-7/8", 12 Bolt. Suspension: Leaf springThis is just a simple video part of the ls Swap Jeep Ford 8.8 axle build showing what the axle tag means.The Dana 50 was an option on the Ford F-250HD (Heavy Duty - over 8500# GVW) from 1980-1986. In 1987, the Dana 50 TTB replaced the Dana 44HD TTB in the F-250 becoming the only option. The Dana 50 TTB remained the front axle in the Ford F-250 4×4 until 1998. All Dana 50 TTB (and Dana 44HD TTB) trucks were leaf sprung and used a single gas shock.

The right ratio. If the tag reads S806D the axle was made for a F 150 Pickup 87-95, E150 Van 87-95, Bronco 87-95. It is a 8.8 In. with a gear ratio of 3.08. It is also a unlocking diff. Hope this clears anything up. Ralph [email protected]. Reply Like. # 8. 09-18-2010, 03:03 PM.1973 - 1979 F-100 & Larger F-Series Trucks - Front axle identification? - I have a 1979 Ford F150 Ranger, I got a Ford 9 in the rear. I looked up the numbers from the vin plate and it says the first two numbers identify the rear axle...ok I go it (H2) which is a ford 9 Now it say the third number identifies the front...Dana 44: The ID tag is under one of the bolts that holds the inspection cover on. It will either have a Ford ID number like: D4TA-AA, or a 7 digit number similar to what the 60's use. It may also have the ratio. If Limited Slip (LS), it will have an L between the first and second numbers of the ratio (example:3 L 55). Lincoln Mark Series 72. 3.00. 9 3/8. NL. 31. full round flange. WGB-AA. Lincoln Mark Series 76-77. Thunderbird 76. Front Axle Identification. To help you find the right part, we first need to properly identify the axle you have or need. Not all vehicles are set up the same, even though they may be the same make and model. ... FORD FRONT AXLES . Find your Ford vehicle in the chart below and click on the illustration for a larger view. Year. Vehicle. Model ...The different types of early Ford axles are easy to identify by referring to the picture on the right, which was scanned from an old magazine article that was written by Neal East. The 1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches. 1932 axles were the first Ford axles to be made with a ...

Food stamp office bx ny.

Common rear end axle codes for Ford vehicles. Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include “C6” for a 3.55 gear ratio, “F6” for a 3.73 gear ratio, and “H9” for a 4.11 gear ratio. It is essential to consult the specific axle ...Contact. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 15. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 15. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L.1977 Ford Axle Codes: Below is a axle code chart from 1977: There's no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you'll see a sticker like the one shown below: You'll see that the area labeled (F) is for the Axle Code.The AXLE code usually contains 3 digits, the first 2 are for the rear axle, but these digits are missing because the truck was a Domestic Special Order. Rear axle was installed after the truck left the assembly line. N = Ford 9,000 lbs. Capacity Front Axle with Power Steering. 27,500 lbs. Gross Vehicle Weight Rating. 730104:Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Reply With Quote. Assuming a its got Ford PCD, the pigs head looks like an English See Burtons catalogue. I eat to survive. I drink to forget. I ...

Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA: Ford Pass., Mercury '77-'78: 2.47: 8.75: NL: 28:Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA: Ford Pass., Mercury '77-'78: 2.47: 8.75: NL: 28:Ford Rear Axle Assembly Identification - Page 08: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WFG-A: Ford Pass., Mercury '70-74: 2.75: 9 in: L: 28-WFG-A: Ford Pass., Mercury 70-74:409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches.The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of vehicles. Starting in 1972, modern factory Dana 44’s had 30-spine axle shafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline). Spicer (Dana) 44 axles use an 8-1/2-inch ring gear bolted to the carrier by 10 ...Check out Torque King's Ford Dana Super 60 front axle identification diagrams online. Learn more about Ford Dana Super 60 front axles for 2005-2016 F250, F350, F450, and F550 Super Duty 4x4 trucks. Download our Ford Dana 60 front axle identification specs (IDN-118). Menu. Search. Close Search. 1-406-384-0270; Call Us 1-406-384-0270;1977 Ford Axle Codes: Below is a axle code chart from 1977: There's no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you'll see a sticker like the one shown below: You'll see that the area labeled (F) is for the Axle Code.Re: Rear Axle Identification. The right side (passenger) is of the '15 era - no reinforcing ribs on the backing plate, the left side (driver) would be in the '17 - '25 vintage. Closed driveshaft bearing spool is in the '10 - '20 era. There are subtle differences in the spool but I'm generalizing.Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include “C6” for a 3.55 gear ratio, “F6” for a 3.73 gear ratio, and “H9” for a 4.11 gear ratio. It is essential to consult the specific axle code chart for the vehicle to accurately ...

Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1987 - 1996 F150 & Larger F-Series Trucks. 1 TON Axle Identification. Notices. 1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by:

Looking to identify my front axle, these are pictures of the tag. Tag is very dirty making it hard to read. Ford: D7TA-ANA / Dana: 603808-9 = Dana 44.7F Front Driving Axle / 3.50-1 / Free Running Hubs / No Limited Slip / 3,500 lbs. Capacity. Tag is very dirty making it hard to read.Ford switched from 28-splines to 31-splines halfway through the 2005 model year. Your date code appears to be a late '03 axle so it'll be a 28-spline. Once you find the axle code, it's pretty easy to translate it. I have a spreadsheet of all (or most) Panther axle codes and their respective gear ratios saved somewhere. _____BRONCO M220 REAR AXLE ASSEMBLY 4.70 RATIO W/ELECTRONIC LOCKING DIFFERENTIAL. M4000470B. $2,485.00. or redeem up to 497,000 Points.External Identification Characteristics of Ford F250 Dana 44 Twin Traction Beam Independent Front Suspension Front Axles: Leaf Spring Suspension; Left and Right Axle Beams formed from stamped and welded steel; Outer End of Internally Splined Wheel Hub is approximately 3-5/8" in diameter; Axle Shaft Universal Joints have Internal C-Clip type ...Ford axle code 39 is a specific code assigned by Ford to identify the type and specifications of the rear axle in a vehicle. The axle code indicates specific details such as gear ratio, differential type, and other important information related to the axle assembly. Understanding the axle code is essential when it comes to replacing or ...Locate the section labeled “F” on the door sticker. Identify the combination of letters and numbers in this section. Refer to the axle code chart for your specific Ford …Pre-Power Stroke Diesel (7.3L IDI & 6.9L) - Axle identification help...it's broken - Good Grief. Had to test the 4x4 for the first time after the snow we got overnight and it broke! Guess that's what tests are for lol. Anyhow can anybody help identifying this axle and the broken part for me please? Dana 44 or 50 IFS?...Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1973 - 1979 F-100 & Larger F-Series Trucks. ... Axle Identification. Hoping someone can help me identify what axle I have on my truck. I've searched the bom, yet nothing comes up. BOM: 603801-10 Thanks Reply Like

P144a lincoln mkz.

Memphis car crash today.

The 1957-1959 Ford styling revolution brought such cars as the Mystere show car and the Skyliner. See pictures and learn all about 1957-1959 Ford styling. Advertisement The 1957 st...Ford ID number: E4TA-AKD / Dana ID number: 610229-2 = Dana 44 / 3.54-1 / Free Running Hubs / non Limited Slip / 3850 lb Front Axle Capacity. 1980/89 Ford Light Truck Parts Catalog, Front Axle Parts List # 30.3AR.The quickest way to tell which axle your Bronco has is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle. On a Dana 44, you will see a large castle nut threaded onto a ball joint. On a Dana 30, you will see a king pin cap with four bolts threaded down into the top of the knuckle.You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 02. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines.Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code: Visit the RV & Trailer Towing Guides page on the Ford Fleet website. Select the Towing Guide for your vehicle's model year. Note: Rear axle ratios are available for 2008 and ...Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA: Ford Pass., Mercury '77-'78: 2.47: 8.75: NL: 28:Using the Ford Axle Code Chart. Our comprehensive Ford axle code chart is a valuable resource for decoding axle codes. It lists all the known axle codes for various Ford models, allowing you to match the code found on your vehicle with the corresponding differential information. See also Reviving Performance: BMW 340i GT xDrive Wheel Bearing ...1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by: 99 - 04 Front Axle ID. Reply Subscribe ... 99 - 04 Front Axle ID. I'm contemplating swapping the Dana 50 in my Excursion for a Dana 60. They are fairly plentiful on CL and prices start around $150 to $200.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear End Tag No. - Identification Help. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:The Following Is a List of Common Dana 61 BOM Numbers - These Axles are NOT Dana 60 Axle: 603925-1. 603946-1. 605022-17. 605039-7. 605064-4.The Following Is a List of Common Dana 61 BOM Numbers - These Axles are NOT Dana 60 Axle: 603925-1. 603946-1. 605022-17. 605039-7. 605064-4. ….

1994 Ford Mustang Axle Information & Ratios. Your Mustang will be equipped with a Vehicle certification label on the driver’s side door jam. This label will show your axle code under the “AX” slot. ... Axle identification: Ratio and Type: 8: 2.73 Axle Ratio – Conventional: M: 2.73 Axle Ratio – Limited slip: 7: 3.07 Axle Ratio ...The Ford 8-inch uses a third member that houses the differential gears. It is bolted to the axle’s housing from the front, which differentiates it from the 9-inch, whose third member is accessed by removing it from the rear of the axle. Bolt count. On an 8 inch differential, there are 10 bolts securing the third member to the axle’s housing ...Rear axle tag identification. I am trying to identify what kind of axle I just purchased. I was told it came out of a '66 Mustang Coupe with a 289. The axle tag reads: According to fordifcation.com they identified this axle coming out of a '65-'66 Mustang with a 2.80 axle ratio and a 7-3/4" ring gear.Quick ID guide for the Ford 8 in. and 9 inch rear axle. We look at how to determine Equa lok, traction lok and open differentials. We show the best and worst...Clutch, Transmission, Differential, Axle & Transfer Case - Axle ID from tag - I found what I think is a ford 1 ton 3 L 55 rear axle in the junkyard today. Can anyone tell me what this axle really is? TAG INFO: V107C 3 L 55 10 2 9C31Axles are 49 7/8″” in total length. Radius Rod Centers are 38 1/2″. 1942-1948 Spring perch bosses are 2 1/4″. Axles are 52″” in total length. Radius Rod Centers are 40 3/4″. 1948 axles have an extra hole in the beam for tube shocks. This first article will help you identify different parts quickly. This particular guide shows the ...Good news is, if you ever break it you only have to buy a new axles from the ball joints in if you upgrade to a 60, just the carrier and center section are different if I am not mistaken. -Aaron 2000 Ext. Cab F350 SRW, 6" Skyjacker lift on front/8" BDS Springs on rear w/NO blocks, 37x13.50 Nitto Mud Grappler's, Aftermarket Front BumperThe rear axle should also have a tag normally on the right front side between the 3rd member and spring pack Most diesel apps for those models used gearing in the 3.73-4.77 range, gas apps normally were in the 5.13-6.50 rangeWith a rear-end gear ratio of 3.73, the pinion will turn 3.73 times for every turn of the ring gear. For a 4.10, the pinion will turn 4.10 times. For a method to manually find out what gear set is installed in your Ford Mustang rear end and for more info on a performance upgrade for your Mustang, check out our 3.73 Gear Ratio vs. 4.10 Ratio ... Ford axle identification, In conclusion, decoding Ford axle tag codes is essential for identifying the specific details of the axle installed in a Ford vehicle. Understanding the axle ratio, differential type, ring gear size, manufacturing plant, and date of manufacture allows owners and mechanics to make informed decisions regarding repairs, upgrades, and vehicle ..., Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-, All Dana axles have a Bill of Materials (BOM) number stamped into the long axle tube that can be used to look up many of the axle's important details including the gear ratio, ring gear rotation, differential type and spline count, as …, Clutch, Transmission, Differential, Axle & Transfer Case - Tranny & Axle Identification - I had my truck up on my dad's hoist and was checking my manual transmission and rear differential fluid. They both seemed fine but I was wondering what kind of fluid they take in case I want to change it with synthetic. The rear..., 1966 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: 2: 2.83 open differential: B: 2.83 locking differential: 1:, Front Axle Identification. To help you find the right part, we first need to properly identify the axle you have or need. Not all vehicles are set up the same, even though they may be the same make and model. ... FORD FRONT AXLES . Find your Ford vehicle in the chart below and click on the illustration for a larger view. Year. Vehicle. …, Originally Posted by Jimmyspy. If it's actually from a level II, it's a 4.10 31 spline 8.8 with a Torsen L/S. From what I can tell, that's for a a 4.10 L/S 8.8. To confirm if 31 spline, measure the axle tubes. 31 spline axle will have larger axle tubes. The axle tubes are 3.25 inches., Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application ... Ford Pass., Mercury '67-'69: 3.10:, If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar (included because 4.10 gears and limited slips are more common than you'd expect) Aerostar., Ford Rear Axle Assembly Identification - Page 13 - FORDification.com. Good job, I agree, looks like you have the 4.30 diff. Im going to check mine tomorrow. Reply Like #4 01-10-2014, 09:20 PM sccamper. Mountain Pass. Join Date: Jun 2012. Location: Upstate, SC. Posts: 182 Likes: 35 Received 26 Likes ..., E-350 Dana axle M70FF (M267FF). 3.28 qt (3.1 L) 1. E-450 Dana axle M70HD (M273HD). 4.86 qt (4.6 L) 1., Looking to identify my front axle, these are pictures of the tag. Tag is very dirty making it hard to read. Ford: D7TA-ANA / Dana: 603808-9 = Dana 44.7F Front Driving Axle / 3.50-1 / Free Running Hubs / No Limited Slip / 3,500 lbs. Capacity. Tag is very dirty making it hard to read., Feb 9, 2006 · Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. F350 Axle identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by: , Clutch, Transmission, Differential, Axle & Transfer Case - Tranny & Axle Identification - I had my truck up on my dad's hoist and was checking my manual transmission and rear differential fluid. They both seemed fine but I was wondering what kind of fluid they take in case I want to change it with synthetic. The rear..., Here's a little information on Late model Mustang rear axle ratios. 1979-2014 Mustangs came equipped with one of two Ford rear ends. Ford 7.5 differential OR 8.8 differential. All '79-85 Mustangs featured the 7.5 rear ends. From '86-2010 the Ford Mustang 8.8 rear end went into all V8 Mustangs (5.0L, 4.6L & 5.4L) The 7.5" rear end went ..., Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. F350 Axle identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:, 2009 - 2014 Ford F150 - Axle tag id ON AXLE ITS SELF!!! - so, my local pull it yourself LKQ got a bit of a unicorn middle of last month they got a 2013 F-150 ext cab hit hard in the front. First time I have seen our body style at that yard. The engine and trans were already taken. it is a VERY low miles truck I got..., So you may well have a 1980 Escort Mk2 Timken axle with Capri Mk2/3 Atlas brakes. The drums appear to be the 1-3/4" wide shoe type (4-cyl), rather than the 2-1/4" wide V6 type. The upper clamps, yes, are for an ARB, which the Capri used after 1972 in place of radius rods (1969-72). Norm., Differential Identification is the first and most important step in any differential repair or ratio change. Careful differential identification will help make sure you get the right parts for the job the first time. Dana Spicer and Ford Differentials can be identified most accurately by the tag number or axle tube stamp. Go to: Differential Tags , The vehicle identification number for Ford cars and trucks is a 17-digit series of numbers and letters that identifies an individual vehicle and certain aspects of the vehicle’s co..., Axle identification. I just bought a 2001 F350 with the 7.3L. I was just wondering if anyone would be able to tell me for sure what axles I have in both the front and the back. Ive heard a bunch of different crap from people about DANA 50, DANA 80s, and the ford 10.25". I figured i could probable figure it out by looking at the vin or crawling ..., 1985-1991 Ford F350 Dana 60 Identification. The open knuckle, monobeam, Dana-Spicer Model 60 was reintroduced by Ford as a mid-year design change in the 1985 model year F-350 1 ton 4x4, replacing the Twin Traction Beam IFS Dana 50 4600 pound rated axle which was used on F-350 trucks starting in the 1980 model year., Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip., While several factors affect the towing capacity of a 2015 Ford F-250, the general maximum range is between 12,400 and 14,000 pounds for a conventional trailer. A four-wheel drive ..., The 1990/2002 Ford Truck Parts Catalog sez: 1996 thru 2002 (prolly later, dunno for sure), uses the Dana Model 286 (80) which has an 11.25" ring gear. On 2000's only, Ford also offered the Dana Model 267 (70). This rear end has a 10.50" ring gear. The AXLE code will be listed on the Certification Label prolly located on the door jamb (B pillar)., Ford used Coil Spring, Dana 44IFS Twin Traction Beam front axles on 1980-1996 Full Size Bronco and F150 4x4 vehicles. These Ford Dana 44IFS front axles are rated at 3500 to 3550 pounds. External Identification Characteristics of Ford Dana 44 Coil Spring Twin Traction Beam Independent Front Suspension Front Axles: Coil Spring Suspension, Common rear end axle codes for Ford vehicles. Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include “C6” for a 3.55 gear ratio, “F6” for a 3.73 gear ratio, and “H9” for a 4.11 gear ratio. It is essential to consult the specific axle ..., 409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches., When it comes to maintaining and repairing your vehicle, using high-quality auto parts is essential. One name that stands out in the industry is Detroit Axle. With their reputation..., The axle code can typically be found on the vehicle’s door tag, which is located on the driver’s side door jamb. It may also be stamped on the axle housing itself …, DRW use a dana rear axle, never a sterling. It was either D80 or D110 depending on year. '99 front axle was a solid Dana 50 (dana 44 center section with dana 60 axle tubes), after '99 it was replaced with the dana 60. Before '99 it was a dana 50 twin traction beam and most parts are interchangeable with the solid axle dana 50., If you knew the Ford and/or Dana ID numbers, you could look them up in the front driving axle cross reference guide (Text-Section 30 - Page 2). P 73/75 4.55 3.5M Dana (Spicer) 6CF W/power strg. --7 6 3.55M Dana (Spicer) 60F W/power strg. I couldn't tell if that was a 5 or 6, now it makes sense., 28. D070-A. Tempo, Topaz 90-92. S102A. Ford F250 Pickup '97-99 (under 8500 GVW) Ford F150 Pickup '00 (7700 Series) 3.31.